Aluminum. Aluminum is corrosion resistant and light weight. It has a lower structural stiffness than steel (about 1/3), which must be compensated for by thicker gauge.
Aluminum for General Purpose EnclosuresAluminum. Aluminum is corrosion resistant and light weight. It has a lower structural stiffness than steel (about 1/3), which must be compensated for by thicker gauge.
Aluminum Sheet. Aluminum sheet metal comes in a variety of thicknesses and weights in many different grades. Ryerson offers heat treatable aluminum sheet grades, like the popular 6061 aluminum alloy, that can be used for commercial applications that require strength, corrosion resistance and machinability, as well as non-heat treatable grades when formability and weldability are priorities.
Carbon Steel |Sheet Steel |Rolledsteel « Rolled Tel:800.400.7833 323.723.8836 Fax:323.888.9866 2187 S. Garfield Avenue Los Angeles, CA 90040
Chart - Bead Hole Sizes - Fire Mountain Gems and BeadsChart includes hole sizes for a range of bead types, with the maximum diameter of Accu-Flex® beading wire and wrapping wire gauge that will fit each hole.
Conveniently determine the diameter, in inches or millimeters, of wire gauges from 10 to 38 gauge.
Copper Sheet Thickness Guide BasicCopper8 MIL (.008 inches thick) 32 gauge:The 8 mil copper is approximately 11 - 12 times thicker than typical household aluminum foil and 1.5 times thicker than the 5 mil. This is a heavy-duty tooling foil. 8 mil can be cut fairly easily with scissors and is still very pliable. It may hold shape a little better than the 5 MIL, but will not bear much weight and will yield to increasing pressure.
GAUGE TO THICKNESS CHART - MetaltroneGAUGE TO THICKNESS CHART Gauge Stainless Galvanized Sheet Steel Aluminum Fraction inches (mm) inches (mm) inches (mm) inches (mm) 30 0.0125 (0.33) 0.0157 (0.40) 0.0120 (0.30) 0.0100 (0.25)
Tel:800.400.7833 323.723.8836 Fax:323.888.9866 2187 S. Garfield Avenue Los Angeles, CA 90040
Gauge Chart Cumberland Diversified MetalsStainless Steel Gauge Chart per ASTM:Gauge:ASTM:Nominal:max:min. 28 Ga:mm:0.41:0.45:0.37:Cold Rolled:inch:0.0160:0.0175:0.0145:26 Ga:mm:0.45:0.49:0
Gauge Weight Chart - metals4uonlineGa# Sheet Steel Galvanized Steel Stainless Steel Aluminum Strip & Tubing; Ga (in.) Wgt (lb/ft 2) Ga (in.) Wgt (lb/ft 2) Ga (in.) Wgt (lb/ft 2) Ga (in.) Wgt (lb/ft 2) Ga (in.) 38:0.0060
Nov 18, 2010 · G60 is a hot dip galvanizing specification for .6 oz total weight of zinc per square foot (approx. 0.0005" thickness per side), whereas there is a different spec for electrogalvanizing wherein 60G60G means each side is plated to a weight of 60 g/m2.
Metal Roofing Gauges:22, 24, 26, & 29 - Metal Roof Panel For example, a 26-gauge steel panel can range between 0.0179 and 0.0217 inches thick according to a University of North Carolina at Chapel Hill resource. This means that while a 26-gauge panel from one manufacturer could measure 0.027 in. thick, a 26-gauge panel from another manufacturer could measure only 0.0179 in., but both are sold as 26
SHEETS GUAGE THICKNESS IN WEIGHT PER SQ. Ft. Kgs. m.s. flat bars width in mm thickness in mm. 5 6 8 10 12 0.5 0.6 0.8 0.9 16 0.6 0.8 1.0 1.3 20 0.8 0.9 1.3 1.6 25 1.0 1.2 1.6 2.0
Sheet metal thickness is denoted by gauge, sometimes spelled gage, which indicates a standard thickness before processing. Click here for a Gauge to mm Conversion Chart. Processing may include polishing, or the applying of protective plastics which will decrease or increase a sheets thickness respectively. .109 - .125.0045.005.132 - .146
Steel Gauge Thickness Guide:MM Charts & Conversion TablesThere are actually two gauge systems that can be use:the US Standard Gauge System and the MSG system or also known as the Manufacturers Standard Gauge system. The US standard gauge system usually uses the value from 2, 1, 0, 2/0, 3/0, 4/0, 5/0, 6/0 or 7/0. MSGs largest thickness in
Tubing - Pipe, Tubing and Fittings - Grainger Industrial Our assortment of pipe tubing and plumbing tubing can safely transport most gases and fluids. Find the specific tubing you need at Grainger.
Mesteel - Steel Thickness Conversion Tables tables. Convert Gauges, BWG, USG to inches and millimeters
Gauge Conversion Chart and Conversion TablesGauge:Nominal Thickness:Min. Thickness:Max. Thickness:No. mm:inches:mm:inches:mm:inches:10:3.43:0.135:3.28:0.129:3.58:0.141:11:3.05:0.120:2.92:0